Speco Technologies Camcorder HTSD10X User Manual

HTSD10X  
10X Pan-Tilt Speed Dome Camera  
200 New Highway, Amityville, NY 11701  
800-645-5516  
 
WARNING & CAUTION  
If you fail to read this information and  
handle the product incorrectly, serious  
injury may occur.  
This symbol is intended to alert the user to  
the presence of un-insulated dangerous  
voltagewithin the products enclosure that  
may be of sufficient magnitude to  
Never install the product in area exposed to  
oil or gas.  
constitute  
persons.  
a
risk of electric shock to  
Never install the product on a ceiling that  
cannot hold its weight.  
This symbol is intended to alert the user to  
the presence of important operating and  
maintenance (servicing) instructions in the  
literature accompanying the appliance.  
Never touch the power cord with wet hands.  
Clean only with a dry cloth.  
Warning  
Never install the product in extreme high or  
low temperature.  
Never move Pan/Tilt by hand. It may  
causes serious damage to the camera.  
Never drop hit strongly or vibrate the product.  
Never touch the front glass of the product.  
Whats in the Box ?  
1. Camera  
2. Screws ( Ø4x16 screw  
3. Terminal block (5pin 2EA)  
4. Manual  
5EA )  
5. Screw Cap (2 EA)  
3
 
GENERAL FEATURES  
100X Zoom Mini Speed Dome  
Quick Operation Keys  
10X Optical Zoom with 10X digital zoom  
This camera provides quick functional keys in order to  
be easily controlled by any controller or DVR.  
±0.02° dome system accuracy  
Various Surveillance Functions  
Auto Scan repeats pan and tilt between two preset  
positions with different speed and dwell time.  
8 Group Tour up to 8 Programmable Group tours  
available and each group consists up to 60 presets with  
different speed and dwell time with 16 characters.  
164 Preset positions up to 164 programmable  
preset positions are available with 16 characters  
8 Patterns up to 8 programmable user-defined patters  
are available with 16 characters and each one is  
consisting 50 seconds, total 400 seconds.  
With 0.1° technical accuracy, camera provides excellent  
sensitive and delicate controlling on preset mode by  
adapting 1/4 micro step and twin gear system  
360° Endless Rotation  
10X mini speed dome is capable of endless rotation of 360  
degrees  
8 Sectors up to 8 programmable user-defined sectors  
are available with 16 characters  
4 Privacy Masking Zones up to 4 programmable  
user-defined privacy masking zones are available with  
16 characters  
Compensation function: preset position  
The function minimizes the appearance of shaky images  
caused by low-frequency vibration, wind and any impact  
and maintains a normal horizontal resolution and sets the  
starting point of pan/tilt on preset mode by using joystick  
turning one time without turn off the power of the camera.  
It is useful for outdoor surveillance and traffic monitoring  
applications.  
4 Alarm input up to 4 alarms activate with preset,  
tours, patterns.  
200°/S Manual speed  
Over 200°/Sec Preset Speed  
This camera provides up to 200°/sec of manual speed  
and its adjustable from 10°/sec to 200°/sec by each  
10°/sec  
The 360° full pan function moves through a maximum of  
200°/sec., enabling you to quickly pinpoint the spot you  
want to watch. Tilt speed provides through a maximum  
200°/sec on preset.  
1/4Sony Super HAD CCD  
Equipped with Sony Super HAD CCD technology, these  
cameras provide excellent sensitivity and low smear  
levels.  
Polarity Protection of Power (DC12V)  
Filter changeable - True Day/Night  
Surveillance with optimum picture is possible owing to filter  
changeable Day/Night (ICR block filter) function and DSS.  
Intelligent Pan/Tilt Controlling  
Intelligent Pan/Tilt function continually decreases pan  
and tilt speeds in proportion to zoom.  
Indoor / Outdoor applications  
Aluminum case and PC cover  
Aluminum body and Poly Carbonated dome cover  
(IP66 Rated)  
.
Password Protection  
4
 
NAMES OF EACH PART  
1. Surface Mount Adaptor  
2. Cap Screw ( PT3/4 , 2EA )  
3. Dip Switch  
4. Terminal Block  
5. Main body  
5
 
INSTALLATION  
A. CONNECTION METHOD  
A-1  
1. Loosen the screws on the domes cover and remove it from the base.  
(Screws will not come out)  
2. Loosen the screws which connect the mount cover and Main base and separate the dome cover  
from the main base. (Screws will not come out)  
3. Connect power (12 VDC 1.5 A ) to Power and GND.  
4. Connect video to Video and GND.  
5. Connect communication cable to RS-485 connectors.  
6. Connect alarm cable to GND like 1 and GND, 2 and GND, 3 and GND, 4 and GND.  
(You can use both N.O / N.C methods.)  
l
Dont screw too tightly. It can be the cause of defect.  
6
 
INSTALLATION  
B. MOUNT  
1. Attach the surface mount adaptor with 4 screws at the installation site. (FIG.4)  
2. When you use pipe, please note the standard size of pipe. (FIG.5)  
3. Re-assemble the domes.  
7
 
QUICK OPERATING KEYS  
1-64 + preset and 101~200 + preset are used for preset and 65-100 + preset used for functions.  
For example, to enter OSD MENU, press the button 95 +PRESET.  
<Quick Operation Key Table 1, Pelco - D, P>  
Number  
1 ~ 64, 100~200 +Preset  
65 + Preset  
Note  
PRESET  
PRESET STATUS Display Preset Status  
Function  
Executing Preset 1 ~ 64  
66 +Preset  
67 +Preset  
71~78 +Preset  
81~88 +Preset  
91 + Preset  
AUTO SCAN  
AUTO FLIP  
GROUP TOUR  
PATTERN  
ZERO POSITION  
FREEZE  
Executing Auto Scan  
Selectable On/Off/Auto in Auto Flip function  
Executing Group Tour #1 ~ #8  
Executing Pattern #1 ~ #8  
92 + Preset  
93 + Preset  
94 + Preset  
BLC MODE  
D/N MODE  
Selectable On/Off in BLC function  
Selectable Day/Night Mode (Auto/Day/Night Mode)  
95 + Preset  
96 + Preset  
OSD MAIN MENU To enter OSD Main Menu  
FOCUS ADJUST Focus adjusting  
97 +Preset  
ALARM  
Selectable Enable/Disable all Alarms  
<Quick Operation Keys Table 2> Use these function keys if controller has these keys>  
Menu Function  
Tilt Up / Down Sub menu cursor moves up / down  
Pan Left / Right  
Focus Near  
Focus Far  
Enter to the sub menu or status change or decrement  
Using for Enter key when user select YES or NO  
Using for function changing keys when set coordinate  
Status cursor to the right  
Zoom Tele  
Zoom Wide  
Status cursor to the left  
* 65 + preset : Status Report , If user presses any key, it disappears.  
8
 
QUICK OPERATING KEYS  
DIAGNOSTIC  
When the Power is turned on a DIAGONOSTIC is operated.  
The following messages are displayed on the monitor.  
CAMERA ID : 001  
BAUD RATE : 2400 BPS  
WAITING………  
PAN ORIGIN  
CHECK OK  
CHECK OK  
TEST OK  
TEST OK  
TILT ORIGIN  
TX CONNECTION  
CAMERA COMM  
A. Pan Origin Test  
Zero point of Pan is founded after Panning test.  
B. Tilt Origin Test  
Zero point of Tilt is founded after Tilting test.  
C
.
TX connection Test  
Countdown from 60 seconds for TX Connection Test,  
During the 60 seconds the camera must receive a signal from any keys of controller or DVR.  
When received the correct signal, OK is displayed after TX CONNECTION TEST.  
* If Not Testedis displayed on the monitor,  
- Camera did not receive the any signal.  
- Camera did receive the signal but it was not correct.  
- User should check protocol, baud rate and RS-485 connection.  
D. Camera Comm. Test  
Communication test with the camera is automatically checked.  
OK should be displayed in these four tests before installation.  
9
 
OSDMENUSETTINGKis displayed and the camera is  
ready to operate.  
A. OSD MENU TABLE  
10  
 
OSD MENU SETTING  
To enter the OSD Menu, press the button 95 + PRESET.  
MAIN MENU  
DOME SETUP  
CAMERA SET  
AUTO SCAN  
TOUR  
PRAVACY  
PATTERN  
ALARM  
SECTOR  
EXIT  
* Use the joystick up - downto move the position and left - rightto make selection  
B. Dome Setup  
To enter the Dome setup, move the joystick right to move the cursor  
.
DOME SET  
CAMERA ID  
RECOVER  
: CAM1□□□□□□□□□□□□  
: OFF  
MANUAL SPEED : 100°/S  
DEFAULT SETTING  
AUTO FLIP  
ZOOM SPEED  
ALARM  
: OFF  
: FAST  
: DISABLE  
: ENGLISH  
LANGUAGE  
[NEXT PAGE]  
SAVE AND EXIT  
EXIT  
B-1.  
DOME SET - CAMERA ID  
To set camera ID, select up to 16 characters using Joystick left or right.  
Press ZOOM TELE button to move to the next character from left to right direction and  
ZOOM WIDE button to move to the next character from right to left direction  
(Space displays when appears)  
11  
 
OSD MENU SETTING  
B-2.  
DOME SET - RECOVER  
This feature allows the dome to work from the last setting before you use the dome manually  
(Auto scan, group tour, pattern or sectors) , after the set time, even power shut down and it turns  
on again.  
Recovery time can be programmed from 15 second to 90 seconds. The default  
setting is OFF.  
B-3. DOME SET - MANUAL SPEED  
Manual Speed of Pan/Tilt is selectable from 10°/sec up to 200°/sec. The default setting is  
100°/sec  
B-4. DOME SET - AUTO FLIP  
Auto Flip is available and the default setting is OFF. Move joystick right or leftto select ON or  
OFF. The default setting is OFF. This function can be recalled by pushing 67+ preset button.  
B-5. DOME SET ZOOM SPEED  
Zoom speeds are selectable FAST or SLOW mode. Move joystick to the right direction for  
selecting FAST or SLOW. The default setting is FAST.  
B-6. DOME SET ALARM  
All alarms are available when set to the ENABLE Mode. Move joystick in the right or left direction  
to select ENABLE/DISABLE. The default setting is DISABLE. This function can be recalled by  
pushing 97 + preset button.  
B-7. DOME SET - LANGUAGE  
Multiple languages are selectable here. Move the joystick to the right or left direction to select  
a
language. The default setting is ENGLISH.  
B-8. DOME SET [NEXT PAGE]  
DOME SET  
SYSTEM LOCK: : OFF  
[PASS WORD]  
DEFAULT SETTING  
[OSD DISPLAY]  
[SYSTEM STATUS]  
[INITIALIZATION]  
[PREVIOUS PAGE]  
B-8-1. DOME SET [NEXT PAGE] SYSTEM LOCK  
Password protection maintains memorized data. It cannot be adjusted by anybody without the  
12  
 
tem lock status is must set as ON.  
OSD MENU SETTING  
t setting is OFF.  
B-8-2. DOME SET [NEXT PAGE] [PASSWORD]  
To enter this page to set a password, move the joystick to the right direction. The password must be  
set by preset number from 001 to 255 (Default 99)  
A. OSD MAIN MENU TABLE (PAGE 11) The default setting is BLANK.  
ENTER PASSWORD  
BY ENTERING PRESET CODE  
PASSWORD ***  
CONFIRM ***  
Press any number from 001~255 with the preset button on password blank and again to confirm.  
Then CONFIRMEDis displayed on the monitor and the menu will go back to the previous page  
automatically.  
ENTER PASSWORD  
ENTER PASSWORD  
BY ENTERING PRESET CODE  
PASSWORD ***  
BY ENTERING PRESET CODE  
PASSWORD ***  
CONFIRM ***CONFIRMED  
CONFIRM ***CANCELLED  
<CONFIRMED>  
<CANCELLED>  
If the user presses the wrong preset number between PASSWORD and CONFIRM, CANCELLED”  
is displayed on the monitor and if user fails 3 times, the menu will return to the previous page  
automatically * After setting a Password, an operator must press memorize password in order to  
enter OSD MAIN MENU, or to change the data which is memorized originally.  
* An operator must remember the password for the operation. Manufacturer doesnt provide a  
memorized password.  
B-8-3. DOME SET [NEXT PAGE] [OSD DISPLAY]  
OSD ID is displayed if set ON here. Move the joystick to the right or left direction in order to select  
13  
 
OSD MENU SETTING  
OSD DISPLAY  
CAMERA ID  
PRESET ID  
SECTOR ID  
COORDINATE  
[PREVIOUS PAGE]  
: OFF  
: OFF  
: OFF  
: ON  
DEFAULT SETTING  
B-8-4. DOME SET [NEXT PAGE] [SYSTEM STATUS]  
This page shows the information of this camera.  
SYSTEM STATUS  
PROTOCOL  
BAUD RATE  
: PELCO D, P  
: 2400 BPS  
FIRMWARE VER. : 2.00  
UPGRADED DATE : 06.07,22  
CAMERA MODULE : SDM100  
[PREVIOUS PAGE]  
DEFAULT SETTING  
- Protocol and baud rate are shown according to the dip switch setting  
(Refer to page 29, 30 and 31)  
- Firmware version and upgraded date will be changed if upgraded.  
B-8-5. DOME SET [NEXT PAGE] [INITIALIZATION]  
To clear all memorized data for tour, preset, sector, privacy or pattern, move joystick to the right  
direction when the cursor is on [INITIALIZATION]  
INITIALIZATION  
[TOUR CLEAR]  
[PRESET CLEAR]  
[SECTOR CLEAR]  
[PRIVACY CLEAR]  
[PATTERN CLEAR]  
[LOAD OPTIMIZED DEFAULT]  
[PREVIOUS PAGE]  
14  
 
OSD MENU SETTING  
-
To clear memorized data, move joystick to the right direction when cursor is on each  
item.  
TOUR CLEAR  
ARE YOU SURE? YES NO  
TOUR CLEAR  
Press FOCUS NEAR button when the cursor is at YES in order to clear memorized data. Then  
each item such as tour, preset, sector and so on is displayed on the monitor about 2~3 seconds.  
After this process, the menu is returned to the previous page.  
* [PRESET CLEAR], [SECTOR CLEAR], [PRIVACY CLEAR], [PATTERN CLEAR] are same as  
[TOUR CLEAR].  
LOAD OPTIMIZED DEFAULT  
ALL DATA INITIALIZING  
ARE YOU SURE? YES NO  
- To clear all data and return to factory defaults, move the joystick to the right when the cursor is at  
[LOAD OPTIMIZED DEFAULT] to enter the above page.  
- Move the joystick to the right or left direction in order to select YES, press FOCUS NEAR button.  
- Then ALL DATA INITIALIZINGis displayed about 5~7 seconds and then the menu is returned to  
the previous page automatically.  
B-9. DOME SET [NEXT PAGE] SAVE AND EXIT  
To save the memorized data and escape this page, move the joystick to the right when  
the cursor is at SAVE AND EXIT.  
B-10. DOME SET [NEXT PAGE] EXIT  
In order not to save any data and escape this page, move the joystick to the right when  
the cursor is at EXIT  
15  
 
OSD MENU SETTING  
C. CAMERA SET  
CAMERA SET  
FLICKER  
: OFF  
MIRROR  
APERTURE  
D ZOOM  
WB MODE  
PIC FLIP  
BLC  
: OFF  
: 10  
: OFF  
: AWB MODE  
: OFF  
: OFF  
D/N MODE  
DSS MODE  
EXIT  
: AUTO  
: OFF  
C-1. CAMERA SET - FLICKERLESS  
Flickerless feature is selected between 50Hz and 60Hz. The default setting is OFF (NTSC: 60Hz /  
PAL: 50Hz). Set flicker mode ON when power source is in discord with frequency. The default  
setting is OFF  
C-2. CAMERA SET - MIRROR  
This feature creates a mirror image. The default setting is OFF.  
C-3. CAMERA SET APERTURE  
Aperture enhances picture details and sharpness by increasing the gain of the camera and  
sharpening the edges in the picture. The default seeting is 10. (the aperture level is from 00 ~ 15)  
C-4. CAMERA SET D ZOOM  
Move the joystick to the right in order to set as ON. The default setting is OFF.  
C-5. CAMERA SET WB MODE  
White balance functions have 4 modes according to the condition of the lighting. The default setting  
is AWB and it may change the mode option accoding to the lighting conditions as below.  
16  
 
OSD MENU SETTING  
l
l
l
Indoor up to 3,200°K  
Outdoor up to 5,800°K  
ATW Mode - 2,000°K to 10, 000°K  
C-6. CAMERA SET PIC FLIP  
Picture flip feature turns ths picture upside down. Move the joystick to the right or left direction to  
select OFF/ON. The default setting is OFF.  
C-7. CAMERA SET BLC (Back Light Compensation)  
The default setting is OFF and BLC modes can be OFF/ON.  
OFF Backlight compensation is not activated.  
ON Back light compensation is activated.  
This function can be recalled by pushing 93 + preset button.  
C-8. CAMERA SET D/N MODE  
ICR filter is changeable according to the lighting, AUTO NIGHT MODE DAY MODE.  
The default setting is AUTO MODE. This function can be recalled by pushing 94 + preset button.  
C-9. CAMERA SET DSS MODE (DIGITAL SLOW SHUTTER)  
If DSS is turned on the digital slow shutter is working. The DSS will remain open to receive some  
more lighting.  
The default setting is OFF.  
C-10. CAMERA SET EXIT  
To escape this page, move the joystick to the right direction.  
17  
 
OSD MENU SETTING  
D. PRESET SET  
To enter PRESET SET, move the joystick to the right direction.  
PRESET SET  
PRESET NO :001  
PRESET ID :PRESET001-------  
PAN :XXX.XX TILT : XXX.XX  
SAVE  
EXIT  
DEFAULT SETTING  
D-1.  
PRESET PRESET NO.  
Up to 164 numbers of preset positions are available. Move joystick to the right or left direction to  
select a preset no.  
D-2. PRESET PRESET ID  
To set preset ID, select up to 16 characters using Joystick to the left or right.  
Press ZOOM TELE button moves to the next character from the left to the right direction and  
ZOOM WIDE button moves to the next character from the right to left direction  
(Space displays when appears)  
D-3. PRESET PAN: XXX.X TILT: XX.X  
Press FOCUS FAR button in order to set the preset position, then use the joystick to move the  
camera to the position where the memorized preset no. is needed. Then press FOCUS FAR button  
again after setting a preset location.  
D-4. PRESET SAVE  
Move the joystick to the right when the cursor is at SAVE and then the cursor will be located on the  
Preset ID for the continuous preset No. setting.  
D-5. PRESET EXIT  
To escape this page, move joystick to the right .  
18  
 
OSD MENU SETTING  
E. AUTO SCAN SET  
* 66 + preset button is working as AUTO SCAN after setting.  
AUTO SCAN SET  
START ANGLE  
END ANGLE  
DIRECTION  
ENDLES  
: XXX.X.XX.X  
: XXX.X.XX.X  
: CW  
: OFF  
DEFAULT SETTING  
SPEED  
: 10°/S  
DWELL TIME  
SAVE AND EXIT  
EXIT  
: 03  
E-1. AUTO SCAN START ANGLE  
To set the start angle, press FOCUS FAR button then move the joystick to the starting angle which is  
to be memorized. Press FOCUS FAR button again is to escape.  
E-2. AUTO SCAN END ANGLE  
To set end angle, press FOCUS FAR button then move the joystick to the starting angle which is to  
be memorized. Press FOCUS FAR button again is to escape.  
E-3. AUTO SCAN DIRECTION  
Auto Scan directions are available with two direction as CW or CCW by joystick to the right or left  
direction  
CW: Clock wise direction (Default)  
CCW: Count Clock Wise Direction.  
E-4. AUTO SCAN ENDLESS  
Auto Scan can use endless rotation, move joystick to the right direction in order to select ON.  
Otherwise, the default setting is OFF.  
E-5. AUTO SCAN SPEED  
User can use auto scan speed from 01°/S up to 99°/S and the default setting is 10°/S.  
E-6. AUTO SCAN DWELL TIME  
To select dwell time, move joystick to the left or right direction in order to adjust dwell time. It is  
possible to set from 01 second to 99 seconds and the default setting is 03 seconds.  
E-7. AUTO SCAN SAVE AND EXIT  
To saving the memorized data and escape this page, move the joystick to the right when  
the cursor is at SAVE AND EXIT.  
19  
 
OSD MENU SETTING  
the right .  
F. TOUR SET  
8 Programmable tours can be set and each tour is available to set up to 64 preset steps. After setting  
the data to each tour group, 71~78 + preset buttons are working as group tour # 1~8  
TOUR SET  
TOUR NO  
: 01  
TOUR TITLE  
TOUR STEP  
PRESET NO.  
DWELL TIME  
: TOUR01□□□□□□□□□□  
: 01  
: 01  
: 03  
DEFAULT SETTING  
SPEED  
: 200°/S  
SAVE  
EXIT  
F-1. TOUR SET TOUR NO.  
Max. 8 group tour no. set by the joystick are available.  
F-2. TOUR SET TOUR TITLE  
To set the tour title, select up to 16 characters using Joystick to left or right.  
Press ZOOM TELE button to move the next character from the left to the right and ZOOM WIDE  
button to move the next character from the right to left direction (Space displays when appears)  
The tour title is not displayed on the monitor, but only for the reference of user.  
F-3. TOUR SET TOUR STEP  
Each tour group consists of up to 60 preset steps with different dwell time and speed. It is possible  
to match any preset # for each tour step.  
F-4. TOUR SET PRESET NO.  
The chosen tour step #101 ~200. It is possible to select any preset no. up to 164.  
F-5. TOUR SET DWELL TIME  
Dwell time can be up to 99 seconds from 01 second. The default setting is 03 seconds.  
F-6. TOUR SET SPEED  
Each tour step can be set with different tour speed up to 200°/S and it is selectable from 10°/S.  
Move joystick to the right or left to select the tour speed. The default setting is 200°/S.  
F-7. TOUR SET SAVE  
To save the memorized data and escape this page, move the joystick to the right when the  
cursor is at SAVE  
20  
 
OSD MENU SETTING  
ght  
G. PRIVACY SET  
4 Privacy masking zones are available to block out areas of the scene.  
PRIVACY SET  
PRIVACY NOMBER : 01  
DISPLAY  
ACTION  
SAVE  
: OFF  
: MOVE  
DEFAULT SETTING  
EXIT  
G-1. PRIVACY SET PRIVACY NUMBER.  
Up to 4 privacy masking zones are available.  
G-2. PRIVACY SET DISPLAY.  
Move joystick to the right or left direction to set ON in order to show the selectable block in the  
center of the monitor. This block appears as a translucent blue square when turned ON. The  
default setting is OFF.  
G-3. PRIVACY SET ACTION (MOVE / ADJUST)  
To set the privacy area, press FOCUS FAR button when the MOVE MODE is showing. Then use  
the joystick to the user defined area in order to set the privacy zone. Then press FOCUS FAR  
button again to escape from MOVE MODE.  
To adjust size of the privacy zone, move the joystick to the right or left direction when the cursor is  
on ACTION. After move mode changed to ADJUST MODE, press FOCUS FAR button in order to  
adjust the size of the privacy zone. The size of he privacy zone can be adjusted by using the  
joystick up down or left right,. After adjusting size of the privacy zone, press FOCUS FAR button to  
escape ADJUST mode.  
l
l
ADJUST: You can change the masking size by using the joystick to the left or right direction  
MOVE: You can move the privacy zone by using joystick to the left or right direction  
G-4. PRIVACY SET SAVE  
After setting the privacy masking zone, to save the data, move the joystick to the right direction  
when the cursor is on SAVE. After saving the data, the cursor moves to PRIVACY NO.2  
automatically to prepare the next privacy masking zone.  
21  
 
G-5. PRIVACY SET EXIT  
OSD MENU SETTING  
H. PATTERN SET  
8 programmable patterns are available with 16 characters of title.  
After setting the data to each pattern # 1~8, 81~88+ preset buttons are working as Pattern # 1~8.  
PATTERN SET  
PATT NO : 01  
PATT TITLE: PATTERN01□□□□□□□  
DATA FILL : 0%  
SAVE  
EXIT  
DEFAULT SETTING  
H-1. PATTERN SET PATT NO.  
Up to 8 programmable user-defined patterns set by the joystick are available.  
H-2. PATTERN SET PATT TITLE  
To set PATTERN TITLE, select up to 16 characters using Joystick to the left or right.  
Press ZOOM TELE button moves to the next character from the left to the right direction and  
ZOOM WIDE button moves to the next character from the right to left direction (Space displays  
when appears) Pattern title is not displayed on the monitor, but only for the reference of user.  
H-3. PATTERN SET DATA FILL  
To fill the programming data, press FOCUS FAR button in order to start the data fill up. Filling data  
is programmed according to the joystick movement. Press FOCUS FAR button again in order to  
escape.  
H-4. PATTERN SET SAVE  
To saving the memorized data, move the joystick to the right when the cursor is on SAVE. Then the  
cursor moves to the PATT NO.02 in order to prepare next pattern no.  
H-5. PATTERN SET EXIT  
To escape this page, move joystick to the right  
22  
 
OSD MENU SETTING  
I. ALARM SET  
4 Alarm inputs are available and each alarm can activate presets, group tours or patterns.  
ALARM SET  
ALARM NO  
: 01  
ALARM INPUT: OFF  
ALARM ACT : 001  
SAVE  
DEFAULT SETTING  
EXIT  
I-1. ALARM SET ALARM NO.  
Up to 4 alarms are selectable by using the joystick to the right when the cursor is on ALARM NO.  
I-2. ALARM SET ALARM INPUT  
Input alarm provides two different ways - NC (Normal Close) or NO (Normal Close)  
I-3. ALARM SET ALARM ACT  
Alarm activates various surveillance modes with Preset number up to 164, Group tour up  
to 8, Pattern up to 8. Move the joystick to the right or left direction to select any preset  
number, group tour no. or pattern no.  
I-4. ALARM SET SAVE  
After setting the alarm input parameters, to save the data, move the joystick to the right when the  
cursor is on SAVE. After saving the data, the cursor moves to Alarm NO.2 automatically to prepare  
the next alarm.  
I-5. ALARM SET EXIT  
To escape this page, move the joystick to the right  
* Before activating an Alarm, user must set ALARM ENABLE at DOME SET ALARM ENABLE  
(Refer to page 15)  
23  
 
OSD MENU SETTING  
J. SECTOR SET  
Up to 8 programmable sectors are available with 16 characters.  
This feature is useful to memorize certain locations such as a parking zone, etc.  
When a camera goes through this area, it shows the letter you memorized.  
SECTOR SET  
Start Position  
SECTOR NO  
: 01  
SECTOR ID: SECTOR01□□□□□□□□  
SECTOR START: XXX.X.XX.X  
SECTOR END : XXX.X.XX.X  
SAVE  
End Position  
EXIT  
DEFAULT SETTING  
J-1. SECTOR SET SECTOR NO.  
Up to 8 programmable sectors set by the joystick are available.  
J-2. SECTOR SET SECTOR ID  
To set SECTOR ID, select up to 16 characters by using the Joystick to the left or right.  
Press ZOOM TELE button to move to the next character from the left to the right direction and  
ZOOM WIDE button to move to the next character from the right to left direction (Space displays  
when appears)  
J-3. SECTOR SET SECTOR START  
To set SECTOR START angle, press FOCUS FAR button then move joystick to the left or right  
direction to set the position. To press FOCUS FAR button again is to escape.  
J-4. SECTOR SET SECTOR END  
To set SECTOR END angle, press FOCUS FAR button then move joystick to the left or right  
direction to set the position. To press FOCUS FAR button again is to escape.  
J-5. SECTOR SET SAVE  
After setting the SECTOR position, to save the data, move the joystick to the right when the cursor  
is on SAVE. After saving the data, the cursor moves to SECTOR NO.2 automatically to prepare the  
next SECTOR.  
J-6. SECTOR SET EXIT  
To escape this page, move the joystick to the right  
24  
 
K. EXIT  
e right or left direction then this  
DIP SWITCH SETTING  
A-1. DIP SW SETTING  
This Speed Dome camera provides up to 63 camera IDs, adjustable using the 1st~6th Dip switch.  
Open the camera case to set ID using DIP SW1.  
* Factory default: Camera ID = 1, PELCO-D  
Termination  
Baud rate  
Protocol  
ID Set  
A-2. ID SETTING (1-ON, 0-OFF) (1è10)  
DIP SW  
ID VALUE  
DIP SW  
ID VALUE  
DIP SW  
ID VALUE  
100000XXXX  
010000XXXX  
110000XXXX  
001000XXXX  
101000XXXX  
011000XXXX  
111000XXXX  
000100XXXX  
100100XXXX  
010100XXXX  
110100XXXX  
001100XXXX  
101100XXXX  
011100XXXX  
111100XXXX  
000010XXXX  
100010XXXX  
010010XXXX  
110010XXXX  
001010XXXX  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
111010XXXX  
000110XXXX  
100110XXXX  
010110XXXX  
110110XXXX  
001110XXXX  
101110XXXX  
011110XXXX  
111110XXXX  
000001XXXX  
100001XXXX  
010001XXXX  
110001XXXX  
001001XXXX  
101001XXXX  
011001XXXX  
111001XXXX  
000101XXXX  
100101XXXX  
010101XXXX  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
101101XXXX  
011101XXXX  
111101XXXX  
100011XXXX  
100011XXXX  
010011XXXX  
110011XXXX  
001011XXXX  
101011XXXX  
011011XXXX  
111011XXXX  
000111XXXX  
100111XXXX  
010111XXXX  
110111XXXX  
001111XXXX  
101111XXXX  
011111XXXX  
111111XXXX  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
20  
21  
42  
43  
101010XXXX  
011010XXXX  
110101XXXX  
001101XXXX  
22  
44  
25  
 
DIP SWITCH SETTING  
A-3. PROTOCOL  
7th~8th dip switches are used for Protocol Setting.  
Factory Default: Pelco-D or Pelco-P ( Auto detection)  
DIP SW1- 7  
OFF  
DIP SW1- 8  
OFF  
Pelco-D or Pelco-P  
A-4. BAUD RATE SETTING  
The 9th Dip Switch is used for BAUD RATE setting.  
DIP SW can be changeable to 2400bps, 9600bps.  
Factory Default: 2400bps.  
DIP SW1 9th  
BAUD RATE  
2400  
OFF  
ON  
9600  
.
A-5. 485 TERMINATIONS  
10th Dip Switch is used for 100termination.  
Set on 10th Dip Switch only for the last looped camera from the controller.  
Even in case of only one camera, set on 10th Dip Switch of the cameras.  
26  
 
TROUBLE SHOOTING  
If you have trouble operating in your camera, refer to the following.  
PROBLEM  
SOLUTION  
Check if the power supply is 12 VDC.  
Check if RS-485 communication cable is connected correctly.  
Check camera ID setting.  
Not operating  
Check the termination.  
Check if all the cables are connected correctly.  
Check if the monitor is adjusted correctly.  
Check if video signal line is cut.  
No picture  
Dark screen  
Adjust the monitor.  
Abnormal camera  
Operation  
Check if voltage level is out of the specification.  
Check the termination.  
Check if there is dust on the lens.  
Adjust the monitor.  
If excessive light is seen on a screen, change the camera  
angle or location.  
Screen not clear  
Adjust the lens focus again.  
27  
 
SPECIFICATIONS  
MODEL  
HTSD10X  
Pan Rotation Angle  
360˚ Endless  
Manual  
Preset  
10˚ ~ 200˚/sec  
Max 200˚ /sec  
Pan Speed  
PAN /TILT  
Tilt Rotation Angle  
Manual  
Preset  
0˚ ~ 90˚  
10˚ ~ 200˚/sec  
Max 200˚ /sec  
0.02˚  
Tilt Speed  
System Accuracy  
164 positions with a 16-character label available for each position  
with different speed steps  
Presets  
Max. 8 Programmable group tours (each one consisting of up to 60 preset steps  
with different steps)  
Group Tour  
Auto scan  
Programmable Auto scan  
Pattern  
8 Programmable Patterns (total 400 seconds)  
Privacy Zone  
Sector  
4 privacy zones  
8 selectable Sectors with 16 characters  
FUNCTIONS  
Password Protection  
Alarm Input  
Yes  
4 alarms OFF/NC/NO (with various programmable states)  
Alarm Actions  
Auto Flip  
Activate preset, Group scanning or Patterns  
ON / OFF  
OSD Menu  
Communication  
Protocol  
Multiple Languages on screen  
RS-485  
Pelco D/P  
Power Consumption  
Power Supply  
Construction  
Dimensions  
Weight  
Motor Type  
Micro Steps  
Storage Temperature  
Operating Temperature  
Certifications  
Image Sensor  
9W Max  
12VDC 750mA  
Die-cast , Anti-vandal dome cover  
167.0φ (D) * 167.0mm(H)  
1.5 kg  
POWER  
OTHERS  
Stepper Motor  
1/4 Step  
-40F to +140F  
-14F to +120F  
CE, FCC  
1/4" Sony Super HAD CCD  
811(H) * 508(V) 410K  
CAMERA  
MODULE  
Total  
Image  
Pixels  
NTSC  
PAL  
795(H) * 596(V) 470K  
768(H) * 494(V) 380K  
752(H) * 582(V) 440K  
More Than 500TV Lines  
Number Of NTSC  
Effective  
Pixels  
PAL  
Horizontal resolution  
10x Optical Zoom  
(F=3.8 to 38mm)  
Optical  
Lens  
Digital  
Day & Night (ICR)  
Min. Shooting Distance  
Digital Slow Shutter  
Normal  
10x (100x with optical)  
Auto/ Day/ Night  
0.35m(Wide)/0.8m(Tele)  
2/4/8/16/24/32/64/128/ OFF  
0.7Lux (50IRE)  
Min.  
mode  
Night  
mode  
illumination  
0.02Lux (ICR On)  
Luminance S/N Ratio  
Video Output  
BLC  
More than 50dB  
VBS:1.0Vp-p/75 Ohm  
ON  
/
OFF  
28  
 
NTSC  
ON  
ON  
/
/
OFF (1/100)  
OFF (1/120)  
Flickerless  
AWB/ATW/INDOOR/ OUTDOOR  
DIMENSIONS  
29  
 

Silicon Image Computer Drive SSD DXXXI 4210 User Manual
Snapper Lawn Mower 06134 User Manual
Snell Acoustics Portable Speaker XA 1900THX User Manual
Sony Camcorder SLT A57 User Manual
Sony Computer Monitor SDM S95 User Manual
Sony DVD Player DADC User Manual
Specialized Cyclometer CR2302 User Manual
Speco Technologies Security Camera CVC6146SCS User Manual
Sterling Marine Instruments S 8418 User Manual
Sun Microsystems Network Card GigaSwift Ethernet Adapter User Manual